Download Article

Download Article

Painting an RC body tin can add together customization to your vehicle while making it look brand new once more. A sleeky paint job also helps your RC vehicle stand out from other vehicles in collections or competitions. If y'all've never spray painted an RC body earlier, it may seem difficult. As long as you've got the right spray painting materials and work with precision, though, painting your RC vehicle can be fun and stress-complimentary.

  1. one

    Strip off the existing paint if you're using an old RC body. While you tin can paint an sometime RC body, you lot volition need to remove the pigment commencement. Spray or coat your RC body in a chemic pigment stripper made for polycarbonate lexan. Leave the stripping chemic on the RC torso for the time directed on the cleaner'south instructions (unremarkably 3-12 hours). Scrape off the paint using a sponge or washcloth, then dry out the RC torso off with a dry out cloth.

    • Read the stripping chemical's instructions carefully to ensure your safety while using it.

  2. two

    Trim the torso to your vehicle'southward specifications if yous purchased a new RC body. Trimming the trunk subsequently you've painted it runs the run a risk of take a chance of damaging your pigment. Place the new body over your existing vehicle chassis to test its fit. Note which areas are too large or brush upwardly against the wheels, and trim these areas with a precipitous pocketknife or pair of scissors.

    • Curved bi-scissors are all-time for making smooth, precise cuts on RC car body.
    • Sand the RC body down if the edges are rough or jagged after trimming.

    Advertizement

  3. 3

    Wash your RC vehicle body earlier you start painting. Use a non-abrasive dish soap and h2o to launder the RC torso thoroughly. Brand sure to target any dust and debris so your paint coats are as smooth every bit possible.

    • Dry your RC body off with a soft, lint-gratis textile before painting it.

  4. 4

    Draw your pattern with a marker over the RC torso, if making a complex design. This will serve equally a blueprint for you lot while you're applying masking tape and painting your car. Use a permanent marker then that the lines don't rub off while you paint.

    • If y'all're but applying a new coat of pigment, you lot exercise not need to draw your design beforehand.
    • Keep your design simple and so information technology is easy to paint, especially if this is your offset time painting an RC car.

  5. 5

    Use masking tape to cover the parts you're not painting. Encompass the areas of the design y'all will non be painting the first color with masking tape. Cut out different pieces of masking tape for each color so you tin remove them as you progress through your painting job. Printing the masking tape downwardly firmly to prevent jagged edges.[1]

    • Always paint darkest to lightest so that the darker colors don't accidentally comprehend the lighter ones.
    • Do not rip out the masking tape unevenly. Cut it with a sharp knife or pair of scissors so it tin cover your design cleanly.

    6. Advertizement

  1. i

    Choose a spray paint fabricated for polycarbonate lexan on your RC vehicle. Generic spray paint will not final as long on your RC body and may fade unevenly. Avoid mixing different brands of spray pigment, which can result in splotchy or uneven colors.[2]

    • You lot can purchase spray paint for polycarbonate lexan online or at most craft stores.

  2. two

    Paint your car in a ventilated area, preferably outdoors. Wear safety goggles and a disposable respirator mask to protect your face and rima oris while painting the vehicle. If you're painting your RC body in a garage or shed, open all windows and doors and position yourself as close to the open up expanse as possible.

    • Read the spray paint directions and warnings to use it safely.
    • If you experience nauseated or airheaded, end painting and go out the surface area immediately. Call poisonous substance command for farther instructions.[3]

  3. 3

    Hold the tin two–three inches (5.1–7.6 cm) away from the RC body. Proceed the can at a distance to avoid making your coat too heavy. Several inches or centimeters is unremarkably enough altitude to avoid blotchy areas.[4]

  4. 4

    Spray the RC body from i cease to the other. As you spray, keep the paint tin can moving. Spraying too long in one spot tin can outcome in an uneven paint coat. Inspect your coats and retouch whatever faint or blotchy areas as needed after you've covered the unabridged body.

    5. Advertisement

  1. 1

    Apply additional coats for a darker or richer color. Don't worry if your outset coat is paler than y'all want it to be. Most colors will need ii-3 coats for a total colour. Add as many coats as needed to achieve the color that yous want.

  2. 2

    Let each glaze dry before y'all employ additional coats. The corporeality of fourth dimension the spray paint will accept to dry depends on the brand—it tin take anywhere from xx minutes to an hour. When your paint coat has finished drying, it should turn from glossy to dull.

    • Use a hairdryer to speed up the drying process from an hour to a few minutes. Turn the hairdryer setting to "absurd," position it 2–3 inches (5.one–7.6 cm) away from the RC body, and keep it moving at all times.

  3. three

    Move on to another colour later on yous accept finished with the first. When the last glaze is dry, remove the masking record roofing the area y'all plan to paint a dissimilar colour. Get-go painting that area of the RC body just every bit you lot painted the offset color. Continue painting your RC trunk and removing the masking tape until you lot accept completely painted the vehicle.[five]

  4. 4

    Add together decals to the RC torso later the last color has dried. Decals are slap-up for adding designs that are likewise complicated for masking tape. Place your decals advisedly on the vehicle body to prevent smudging your paint job.[six]

    • Yous might add, for example, racing stripes, flames, skulls and crossbones, swirls, animals, or your/your RC motorcar'southward proper name.

  5. five

    Finish your RC pigment job with a clear coat of spray paint. To keep your spray pigment or decals from peeling off and to requite your RC vehicle a glossy sheen, spray a sparse, clear spray paint over the trunk. Let your last paint coat dry for 30 minutes to an hour before yous play with your RC vehicle.

    • Purchase a clear spray paint that is likewise made for polycarbonate lexan.

    6. Advertizement

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

  • Take your fourth dimension as you pigment your RC trunk. If you lot can go on your hands patient and steady, you lot will end up with a more than even paint job.

    • RC body lids can be purchased online or at some electronics stores.

Thanks for submitting a tip for review!

Advertisement

Things Yous'll Demand

  • Dish soap
  • Water
  • Soft textile
  • Abrupt knife or scissors
  • Marker
  • Masking tape
  • Lexan spray paint
  • Goggles
  • Respirator mask
  • Decals (optional)
  • Hairdryer (optional)

References

About This Article

Thank you to all authors for creating a folio that has been read 30,580 times.

Did this article assist you?